Cu3P and Ni2P co-modified g-C3N4 nanosheet with excellent photocatalytic H2 evolution activities

Copper-nickel phosphides/ graphite-like phase carbon nitride (Cu₃P-Ni₂P/g-C₃N₄) composites were obtained through a facile one-pot in situ solvothermal approach. The coexistence of Cu₃P and Ni₂P plays an important role in enhancing the catalytic activity of g-C₃N₄. The 7 wt% Cu₃P-Ni₂P/g-C₃N₄ bimetallic phosphide photocatalyst demonstrates the best photocatalytic hydrogen (H₂) evolution rate of 6529.8 μmol g⁻¹ h⁻¹, which is 80.7-fold higher than that of g-C₃N₄. The apparent quantum yield (AQE) was determined to be 18.5% at 400 nm over the 7% Cu₃P-Ni₂P/g-C₃N₄. This in situ growth strategy produced intimate contact interfaces, leading to a significantly promoted separation of charge carriers, and hence strengthened the photocatalytic H₂ production. Moreover, the coexistence of Cu₃P and Ni₂P reduced the overpotential of H₂ during the evolution process, further benefiting H₂ production. Finally, the photocatalytic enhancement mechanism was proposed and verified by fluorescence and electrochemical analysis. This work provides a low-cost strategy to synthesize nonprecious bimetallic phosphides/carbon nitride photocatalyst with outstanding H₂ production activity. © 2020 Society of Chemical Industry     

FINE:Future Internet iNnovation Environment

This article introduces FINE(Future Internet iNnovation Environment) project,which is supported by National High-tech R&D Program( "863" Program) of China.     

Enhanced performance by polyaniline/tailored carbon nanotubes composite as supercapacitor electrode material

Polyaniline/tailored carbon nanotubes composite (PANI/TCN) synthesized via situ polymerization of aniline monomer in the presence of tailored carbon nanotubes (TCN) is reported as electrode material for supercapacitors. The morphology, structure, and thermostability of the composite were characterized by scanning electron microscope, Fourier transform infrared, and thermogravimetric analysis. The electrochemical property of the resulting material was systematically studied using cyclic voltammetry and galvanostatic charge–discharge. The results show that the short rod‐like PANI dispersed well in the TCN with three‐dimensional network structure. The as‐prepared composite shows high specific capacitance and good cycling stability. A specific capacitance of 373.5 F g^?1 at a current density of 0.5 A g^?1 was achieved, which is much higher than that of pure PANI (324 F g^?1). Meanwhile, the composite retains 61.7% capacity after 1000 cycles at a scan rate of 50 mV s^?1. The enhanced specific capacitance and capacity retention indicates the potential of composite as a promising supercapacitor electrode material. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014 , 131, 39971.     

高效固体缓释型阻垢剂的研制及性能分析

针对大庆油田集输管道腐蚀结垢现象,以主剂、分散剂、特殊缓蚀阻垢剂和载体配制固体缓蚀阻垢剂,通过复配试验筛选出适合其采出液水质的药剂,并对其缓蚀和阻垢性能进行分析。结果表明:加注药剂后的管道钢腐蚀速率为0.070mm/a,远低于未加注前的0.310mm/a;阻垢效果15天内稳定,阻垢率约为91%,阻垢性能良好;缓释速率为约每10天溶解8%,加注周期约为3个月。所制备药剂性价比高,缓蚀阻垢综合性能良好,可作为油田水驱采出液专用缓蚀阻垢药剂。     

颗粒在椭圆形回转干馏炉内运动分析

通过实验研究颗粒在不同椭圆滚筒内的运动情况,分析了不同填充率、不同转速和不同颗粒粒径对其的影响。由实验得出:颗粒在椭圆不同位置的运动情况并不一致,随着长短轴之比变大,运动趋于平缓;填充率降低会引起颗粒运动模式过渡区间变大,进入小瀑布模式所需转速增加;颗粒粒径增大,颗粒在筒内受重力、摩擦力的影响变得更加明显,在长轴垂直水平位置,所受惯性影响更加显著,并出现明显的多种模式相结合的运动形式。     

基于Fluent的水击泄压阀阻力系数研究

针对长输油管道广泛应用的水击泄压阀,应用CFD方法对其内部流场进行了分析计算。按照实际泄压阀的结构,建立了简化后的二维流场几何模型,根据模拟的流场压力分布计算不同开度、不同开启压力和不同管径下泄压阀的阻力系数,指出泄压阀的阻力系数与开度、管径有关,开启压力对泄压阀的阻力系数几乎没有影响。     

一种新型甲醛处理装置及处理效果研究

针对目前室内装修甲醛严重超标,严重危害人体健康的现状,设计了一个可以在线检测甲醛浓度并采用光触媒技术进行处理的系统装置,并进行了探索性试验.结果表明,在一定的时间和浓度范围内,光照强度越强、甲醛初始浓度越低、光触媒用量越多,甲醛的去除率越高.在实际应用中,考虑时间和成本的因素,可以选择光照强度31 W,甲醛的初始浓度1.6 ppm,光触媒的用量为2.5％,此时甲醛的去除率较高.     

柱前衍生-高效液相色谱法检测安立生坦的手性拆分剂L-脯氨酸甲酯

采用4-氯-7-硝基苯-2-（嗯）-1,3-二唑（NBD-Cl）作为柱前衍生试剂,建立了柱前衍生化-高效液相色谱法（HPLC）结合荧光检测器测定安立生坦合成过程中使用的手性拆分剂L-脯氨酸甲酯的方法.考察了衍生反应温度、时间、衍生试剂加入量、缓冲液pH对L-脯氨酸甲酯衍生反应的影响.结果表明,衍生反应优化条件为：反应温度60℃,反应时间60 min,衍生试剂加入量为每毫升反应体系中加入0.3 mg NBD-Cl,衍生反应缓冲液pH为9.0.同时对此方法进行了方法学验证,L-脯氨酸甲酯在0.625～7.5 μg/mL范围内线性关系良好,r=0.999 4;检测限为2.5×10-3μg/mL,定量限为7.5×10-3μg/mL;平均回收率为91.9％～ 106.4％;重复性实验中RSD为0.33％;此方法耐用性良好,L-脯氨酸甲酯样品溶液及衍生产物溶液体系稳定.此方法灵敏、简便、专属性强,能对安立生坦原料药中残留的杂质L-脯氨酸甲酯进行检测及定量分析.     

300 MW级火力发电机组循环冷却水阻垢缓蚀剂性能研究

以华北地区某电厂的循环冷却水系统补充水为试验介质,以其凝汽器使用的HSn70-1A、HSn70-1B、BFe30₁₁ 3种铜合金为试验对象,采用循环冷却水动态模拟、电化学阻抗谱（EIS）测试、电子显微镜（SEM）观察及金属表面元素分析（EDS法）的方法对2种药剂（A、B）的阻垢缓蚀性能进行了研究。结果表明:现场循环冷却水浓缩倍率维持4倍时,2种药剂均可保障机组安全运行,其中药剂B的缓蚀效果较好。     

羧甲基淀粉接枝共聚物降失水剂研究

以玉米淀粉为原料,对其进行碱化及醚化,将醚化中间体与AM、AA、DMDAAC进行接枝共聚.玉米淀粉羧甲基化的最佳合成条件为：40℃碱化1h,水∶淀粉=1∶1（质量比）,NaOH∶ClCH2 COOH=2.25∶1（摩尔比）,以及醚化时间为3h、温度51℃.CMS与烯类单体接枝共聚的最佳合成条件为：硝酸铈铵∶过硫酸钾=1∶1（质量比）,反应温度55℃,时间4h.接枝共聚产品的降滤失性能有所差异,当各自降滤失性能发挥至极佳时,产品的最佳合成配方也不尽相同.